manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 51 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 51

 

Functions 

 

5.1 Basic functions 

3KC ATC6300 transfer control device 
Manual, 03/2018, L1V30535632002A-01 

49

 

5.1.6.3

 

Alarm table 

The alarms have the following properties (for a definition of the properties, please refer to 

chapter Properties of the alarms (Page 47): 
The properties of the alarms can be modified using Menu P16. This can be selected from the 

setup menu. For information on the selection procedure, please refer to chapter 

Parameterization of the user interface (Page 115). 

 

Code  Description 

Ena-

bled 

Only 

AUT 

Re-

tained 

Global 

alarm 

Lock 

BRK 

1 

Lock 

BRK 

2 

Siren  Lock  No 

LCD 

A01 

Battery voltage too low 

x 

 

x 

x 

 

 

x 

 

 

A02 

Battery voltage too high 

x 

 

x 

x 

 

 

x 

 

 

A03 

Fault breaker Line 1 

x 

x 

x 

x 

x 

 

x 

 

 

A04 

Fault breaker Line 2 

x 

x 

x 

x 

 

x 

x 

 

 

A05 

Line 1 wrong phase sequence 

x 

 

x 

x 

 

 

x 

 

 

A06 

Line 2 wrong phase sequence 

x 

 

x 

x 

 

 

x 

 

 

A07 

Load not powered timeout 

x 

x 

 

x 

 

 

x 

 

 

A08 

External battery charger failure 

 

 

 

x 

 

 

x 

 

 

A09 

Emergency 

x 

 

x 

x 

 

 

x 

 

 

A10 

Line 1 breaker protection trip 

x 

 

x 

x 

x 

x 

x 

 

 

A11 

Line 2 breaker protection trip 

x 

 

x 

x 

x 

x 

x 

 

 

A12 

Line 1 generator not available 

x 

 

 

x 

 

 

x 

 

 

A13 

Line 2 generator not available 

x 

 

 

x 

 

 

x 

 

 

A14 

Maintenance Hours 1 

x 

 

 

 

 

 

 

 

 

A15 

Maintenance Hours 2 

x 

 

 

 

 

 

 

 

 

A16 

Maintenance operations 1 

x 

 

 

 

 

 

 

 

 

A17 

Maintenance operations 2 

x 

 

 

 

 

 

 

 

 

A18 

Auxiliary voltage failure 

x 

 

 

x 

 

 

x 

 

 

 
 

 

Note 
The "Inhibited" and "No LCD" functions are not activated in the factory settings, but can be 

selected or deselected by the user. 

 

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments