Siemens SENTRON ATC6300 Manual Download Page 130

Page: 130 / 210

Parameterization

9.3 Parameters

3KC ATC6300 transfer control device

128

Manual, 03/2018, L1V30535632002A-01

P05
Changeo-

ver

Designation on ATC

display

Description

Unit

Default

Range

P05.20

Closing retry

Closing retry
– In the case of circuit breakers with motor

operators, this parameter specifies in which

mode the new attempt to close the device can

be performed. The new closing attempt is per-

formed when the previous closure has failed,

probably because the springs were not loaded.

It involves performing a complete opening and

spring loading cycle followed by a new closing

command. If the breaker fails to close again,

feedback alarm A03 or A04 is triggered.

AUT

OFF

AUT

AUT+MAN

OSE

P05.21

Gen. Rot. Interval

Generator start interval
- These parameters permit a time-controlled

rotation in the G-G application by switching the

priority between the two generators. Thus a

switch between 2 generators can be imple-

mented at certain times of the day.
P05.21 specifies the rotation interval of the two

generators.

OFF

OFF
1h-2h-3h
4h-6h-8h-12h-
1d-2d-3d
4d-5d-6d-7d

P05.22

Gen. Rotation Hour Generator start hour

- The time of day at which the rotation is per-

formed is specified by P05.22 and P05.23. If

the rotation interval is greater than 24 hours,

the rotation is performed at the specified time

every n days. If it is less than 24 hours, the

rotation is performed at the specified time and

at the respective intervals. If, for example, the

time is specified as 12:30 and the rotation is

every 6 hours, one rotation will take place at

12:30, one at 18:30 the next at 0:30 etc.

0...23

P05.23

Gen. Rotation

Minutes

Generator start minutes

min

0...59

OBP (Open Before Presence) - In the automatic mode the open command of a circuit

breaker is generated (when the line concerned goes beyond limits) regardless of the status

of the alternative line. As a consequence, the priority line is switched off even if the

alternative line is not available.

OAP (Open After Presence) - In the automatic mode the open command of a circuit

breaker is only sent after the alternative line is present within limits.

EJP = Two programmable inputs are used, which can be configured with the functions

Load off and Remote changeover. When the starting input closes, the motor start delay

(P05.14) is enabled, after which the start cycle runs. Subsequently, when the remote

switching go-ahead is received, the load is transferred from the mains to the generator, if the

generator has been started properly. The load is restored to the mains by the remote

switching go-ahead opening and the gen-set runs the stop cycle when the start input opens.

The EJP function is only enabled if the system is in the automatic mode. The safety devices

and alarms function as usual.

Summary of Contents for SENTRON ATC6300



















































































































































































































Search results

Summary of Contents for SENTRON ATC6300

Reviews:

Siemens SENTRON ATC6300, Manual, Page: 130 / 210

Search results

Summary of Contents for SENTRON ATC6300

Reviews: