Siemens SENTRON ATC6300 Manual Download Page 60

Page: 60 / 210

Functions

5.2 Extended functions

3KC ATC6300 transfer control device

Manual, 03/2018, L1V30535632002A-01

Possible reference measurements:

Designation on the

ATC6300

Description

OFF

The user limit is deactivated.

V L1-N

The voltage of L1-N serves as a source for the limit threshold.

V L2-N

The voltage of L2-N serves as a source for the limit threshold.

V L3-N

The voltage of L3-N serves as a source for the limit threshold.

V L1-L2

The voltage of L1-L2 serves as a source for the limit threshold.

V L2-L3

The voltage of L2-L3 serves as a source for the limit threshold.

V L3-L1

The voltage of L3-L1 serves as a source for the limit threshold.

V L-N EQV

The mean value of all voltages between L-N serves as a source for the limit

threshold.

V L-L EQV

The mean value of all voltages between L-L serves as a source for the limit

threshold.

The frequency serves as a source for the limit threshold.

ASY V L-L

The voltage unbalance of L-L serves as a source for the limit threshold.

ASY V L-N

The voltage unbalance of L-N serves as a source for the limit threshold.

CNT x

The user-defined counter CNTx serves as a source for the limit threshold.

CNT AUT

The defined counter CNT AUT serves as a source for the limit threshold.

CNT MAN

The defined counter CNT MAN serves as a source for the limit threshold.

A 03

The occurrence of the alarm A03 (Line 1 circuit breaker timeout) serves as a

source for the limit threshold.

A 04

The occurrence of the alarm A04 (Line 2 circuit breaker timeout) serves as a

source for the limit threshold.

Time Load

The time for which the power is supplied by the selected power supply source

serves as a source for the limit threshold.

No Load

The total time without a power supply serves as a source for the limit thresh-

old.

Switch off

The source for the limit threshold is the number of times that the ATC6300

has been de-energized.

Year

The year serves as a source for the limit threshold.

Month

The current month serves as a source for the limit threshold.

Day

The current day serves as a source for the limit threshold.

Hour

The current hour serves as a source for the limit threshold.

Minute

The current minute serves as a source for the limit threshold.

Sec

The current second serves as a source for the limit threshold.

Week day

The current day of the week serves as a source for the limit threshold.

Summary of Contents for SENTRON ATC6300



















































































































































































































Search results

Summary of Contents for SENTRON ATC6300

Reviews:

Siemens SENTRON ATC6300, Manual, Page: 60 / 210

Search results

Summary of Contents for SENTRON ATC6300

Reviews: