manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 136 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 136

Parameterization 

 

9.3 Parameters 

 

3KC ATC6300 transfer control device 

134

 

Manual, 03/2018, L1V30535632002A-01 

9.3.8

 

P08 - Communication 

This menu is divided into two sections for the communication channels COM1 and COM2.  

 

 

Note 
The parameters for communication only function in combination with the RS485 expansion 

module (3KC9000-8TL74) or the Ethernet expansion module (3KC9000-8TL75). 
The USB front interface (3KC9000-8TL73) has fixed communication parameters and 

therefore requires no setup menu. 

 
 

 

P08 
Communi-

cation 
COMn (n = 

1/2) 

Designation on 

ATC display 

Description 

Unit  

Default  

Range  

P08.n.01  

Serial node ad-

dress  

MODBUS node address  
– Serial address (nodes) of the communication 

protocol. 
 

 

01  

01-255  

P08.n.02  

Baud rate  

Serial speed  
– Transmission speed of the communication 

port. 

bps  

9600  

1200  
2400  
4800  
9600  
19200  
38400  
57600  
115200  

P08.n.03  

Data format  

Data format  
– Setting to 7 bits only possible for ASCII proto-

col. 

 

8 bit – n  

8 bit –no par.  
8 bit, odd  
8 bit, even  
7 bit, odd  
7 bit, even  

P08.n.04  

Stop bits 

Stop bits  
– Number of stop bits. 

 

1  

1 - 2  

P08.n.05  

Protocol  

Protocol  
– Choice of communication protocol. 

 

MODBUS 

RTU  

MODBUS 

RTU 

MODBUS 

ASCII  
MODBUS 

TCP  

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments