Siemens SENTRON ATC6300 Manual Download Page 119

Page: 119 / 210

Parameterization

9.1 Parameterization via the user interface

3KC ATC6300 transfer control device
Manual, 03/2018, L1V30535632002A-01

117

If access is possible, the following window appears:

①

New value entered

②

Maximum possible setting

③

Factory default setting

④

Minimum possible setting

⑤

Parameter code

⑥

Parameter description

This window contains information on the range of values, the minimum and maximum

values, the previous setting, and the factory default setting.

9.1.1

Changing the parameters

●

The parameters can be changed using the + and – keys.

●

Pressing the + and – keys simultaneously leads to the factory setting.

●

For a text string entry, the character is selected using the ▲ and ▼ ke

ys and the cursor is

moved through the text using the + and – keys.

●

By pressing ▲ and ▼ simultaneously in the case of a text entry, the character selection is

set to the letter A.

●

By pressing the ✓ key, the currently selected parameter is stored.

The device then returns to the menu one level above this (in this case, to the P04 Battery

diagram).

●

You can exit the setup menu by pressing OFF.

Note
Restart after parameter change
After each parameter change the device executes a restart. If it remains in the setup menu

for more than two minutes without any changes being made, the device will also restart.

After the restart, the ATC is in the OFF mode.

Summary of Contents for SENTRON ATC6300



















































































































































































































Search results

Summary of Contents for SENTRON ATC6300

Reviews:

Siemens SENTRON ATC6300, Manual, Page: 119 / 210

Search results

Summary of Contents for SENTRON ATC6300

Reviews: