manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 114 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 114

Operation 

 

8.3 Designation and description of the outputs 

 

3KC ATC6300 transfer control device 

112

 

Manual, 03/2018, L1V30535632002A-01 

8.3.2

 

Table of functions of the digital outputs 

The table below lists all functions that can be assigned to the programmable digital outputs 

OUTx.  

 

Function 

Description 

Disabled 

Output disabled 

Configurable 

Free configuration by the user. 

Close Line 1 contactor/circuit breaker 

Command to close the contactor/circuit breaker 

of Line 1. 

Open Line 1 contactor/circuit breaker 

Command to open the circuit breaker of Line 1 

with possible spring load. 

Close Line 2 contactor/circuit breaker 

Command to close contactor/circuit breaker of 

Line 2. 

Open Line 2 contactor/circuit breaker 

Command to open the circuit breaker of Line 2 

with possible spring load. 

Open Line 1 and Line 2 

Open both circuit breakers / neutral position of 

the transfer switching equipment with motor op-

erator. 

Min coil Line 1 

Controls the undervoltage release by opening 

breaker 1 before the spring load cycle. 

Min coil Line 2 

Controls the undervoltage releases by opening 

breaker 2 before the spring load cycle. 

Line 1 generator control 

Control of the Start / Stop remote control of the 

generator on Line 1. 

Line 2 generator control 

Control of the Start / Stop remote control of the 

generator on Line 2. 

ATC ready 

ATC in automatic mode, without alarms, ready to 

switch. 

Global alarm 

Output enabled in the presence of any alarm with 

the property "Global alarm enabled". 

Line 1 status 

This output is enabled if all conditions for the 

connection of the load to Line 1 have been met. 

Line 2 status 

This output is enabled if all conditions for the 

connection of the load to Line 2 have been met. 

Siren 

Supplies power to the siren for the acoustic sig-

nal. 

Operating mode 

This output is enabled if the ATC is in one of the 

operating modes set with parameter P12.03. 

OFF mode 

Enabled if the ATC is in the OFF mode. 

MAN mode 

Enabled if the ATC is in the MAN mode. 

AUT mode 

Enabled if the ATC is in the AUT mode. 

Remote variable REM (x) 

Output controlled by remote variable REMx 

(x=1..8). 

Limit threshold LIM (x) 

Output controlled by the status of the limit thresh-

old LIM(x), (x=1..4); defined by the Index parame-

ter. 

Dummy (dummy load) 

This output is enabled if the automatic test is 

performed with dummy load. 

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments