manualshive.com logo in svg

Siemens LITHOSTAR Multiline, Installation Instructions Manual

Share
Download
Siemens LITHOSTAR Multiline Installation Instructions Manual Download Page 4

0 - 4

Contents

LITHOSTAR Multiline

 

RXL2-120.812.01

Page  4 of  4

Siemens AG

System

Rev. 02

10.04

CS PS 24

Medical Solutions

 

Connections/cable locations in the generator cabinet (Part A) .  .  .  .  .  .  .  .  .  .  .  .  .  3 - 3
Connections of the options and their cable locations in the A12 
electronics cabinet and generator AC   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  3 - 6
Connections and cable locations in the A12 electronics cabinet 
and in the control console   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  3 - 8
Connections/cable locations in the A13 shock wave cabinet .  .  .  .  .  .  .  .  .  .  .  .  .  .3 - 11
Connections/Cable Locations in the Generator Cabinet (Part. B)  .  .  .  .  .  .  .  .  .  .  .3 - 13
Connections/harness locations in the generator cabinet (Part C)  .  .  .  .  .  .  .  .  .  .  .3 - 16
Fastening of plug, Sonoline.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .3 - 20

4 ______ Connections with POLYDOROS SX 65 _____________________________4 - 1

General information   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4 - 1
Connections and cable locations in the A12 electronics cabinet .  .  .  .  .  .  .  .  .  .  .  .  4 - 2
Overview of cable run in the power cabinet   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4 - 3
Connections/harness locations in the generator cabinet (Part A)  .  .  .  .  .  .  .  .  .  .  .  4 - 4
Connections of the options and their cable positions in the A12 
electronics cabinet and generator AC   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4 - 6
Connections and cable locations in the A12 electronics cabinet 
and in the control console   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4 - 8
Connections/cable locations in the A13 shock wave cabinet .  .  .  .  .  .  .  .  .  .  .  .  .  .4 - 11
Overview of cable run in the power cabinet   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .4 - 13
Connections/cable locations in the generator cabinet  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .4 - 14
Overview of cable run in the power cabinet   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .4 - 18
Connections/harness locations in the generator cabinet (Part C)  .  .  .  .  .  .  .  .  .  .  .4 - 19
Monitoring devices and indicators for radiation protection  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .4 - 20
Fastening of plug, Sonoline.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .4 - 24

5 ______ Final Work Steps _______________________________________________5 - 1

Attaching the remaining panels.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  5 - 1
Adapting the Other Accessories  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  5 - 2

6 ______ Changes to previous version _____________________________________6 - 1

Page

Summary of Contents for LITHOSTAR Multiline







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands