manualshive.com logo in svg

Siemens LITHOSTAR Multiline, Installation Instructions Manual

Share
Download
Siemens LITHOSTAR Multiline Installation Instructions Manual Download Page 30

LITHOSTAR Multiline

 

RXL2-120.812.01

Page 8 of 20

Siemens AG

System

Rev. 02

10.04

CS PS 24

Medical Solutions

3 - 8

Connections with POLYDOROS LX 30

 

Fig. 5

Connections and cable locations in the 
A12 electronics cabinet 
and in the control console

3

(cable harness, green)

•

Route the cables in the A12 electronics cabinet, 
as shown in Fig. 5 and connect them as shown in 
Table 5, 6 and 7.

VIDEOMED connection: 

•

Remove the XCS cables X11 and X12 from the D5 
board.

•

Remove the EMC shielding on the Videomed.

•

Route the camera connector D8.X1similar to the video 
cable underneath the rack and connect it to the 
backplane as shown in Table 5.
Remove board D1 for this purpose.

•

Attach the cable with a cable clip to the rack above the 
shield.

•

Attach the EMC shielding on the Videomed.

•

Connect the XCS cables X11 and X12 on the D5 board.

8

8

7

6

9

4

4

5

10

A12

Mounting rail for cable harness

Cable harness, green, from the control console

Cable harness, green, from the unit (K3, K4....)

Cable harness, green, from the unit (K8, K9....)

3rd monitor on the monitor trolley (option)

Video cable 3rd monitor

VIDEOMED

-DIM-

Power Supply

M16

System

Controller

N11

Image Storage

Summary of Contents for LITHOSTAR Multiline







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands