manualshive.com logo in svg

Siemens LITHOSTAR Multiline, Installation Instructions Manual

Share
Download
Siemens LITHOSTAR Multiline Installation Instructions Manual Download Page 40

LITHOSTAR Multiline

 

RXL2-120.812.01

Page 18 of 20

Siemens AG

System

Rev. 02

10.04

CS PS 24

Medical Solutions

3 - 18

Connections with POLYDOROS LX 30

 

Ultrasound option

For 230 V Sonoline line voltage

- Connect the cables to the power line terminal NK 1, 2, 3 (Fig. 15)
- Shielding see A/Fig. 15

For 115 V Sonoline line voltage
(the required parts are located in the 115 V power supply packet)

- Attach the supplied grounded instrument connector (female connector) and the nozzle 

to the 115 power supply cable routed into the case frame by the customer.

- Connect the grounded instrument connector (male connector) and the nozzle to the 

power line cable from the corrugated hose.

- Plug the two grounded instrument connectors together (corrugated hose - power 

supplies).

•

Connect the protective conductor to the clamp (figure 15).

•

Connect the control cable to D31.X28 (figure 15). This is possible only after moving the 
system.

•

Route the fiber optic and video cables to the control cabinet. (Refer to the installation 
instructions for fiber optic cables /module RX0-000.038.02...).

•

Route the video cable into the control cabinet (not used).

•

Connect the ultrasound tableside control to SONOLINE.

•

Connect the ultrasound probe and place the probe in its holder.

•

Move board D6 slightly away from N11 to facilitate this. 

•

Plug the fiber optic cable into N11 on board D6 (according to color code). Secure the 
fiber optic cable with cable clamps to the right side of the cabinet.

•

Connect the corrugated hose to the Sonoline.

Unpack and assemble the SONOLINE according to the instruc-
tions.

Type of Cable Function

Ultrasound 
system

Multiline

ok

Unit

Cabinet A12

1 x 4 mm

2

Protective con-
ductor

Rear panel

Protective 
conductor
terminal

3 x 0.75 mm

2

shielded

Voltage supply

Rear panel

refer to text

Canon
9 pole

Control cable

Ultrasound
tableside control

D31.X28

Fiber optic 
cable

Communication

Rear panel

N11.D6

Video

Rear panel

w/o function

Tab. 11

NOTICE

Summary of Contents for LITHOSTAR Multiline







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands