Siemens LITHOSTAR Multiline Installation Instructions Manual Download

Page: 68 / 70

LITHOSTAR Multiline

RXL2-120.812.01

Page 2 of 2

Siemens AG

System

Rev. 02

10.04

CS PS 24

Medical Solutions

5 - 2

Final Work Steps

•

Remove all the protective plastic foil from the various operating panels.

•

Attach all the cabinet front panels.

•

Seal all seams between the system and the floor with silicone suitable for wet cells
(Fig. 4 and Fig. 5).

•

Complete the installation protocol in register 3 of the log book.

Adapting the Other Accessories

•

Perform a test installation of all accessories that have been included in the shipment in
accordance with the Operating Instructions

System

Insulating plate

Floor

Silicone

Mounting plate

Fig. 3

Fig. 4

Silicone

Fig. 5

Summary of Contents for LITHOSTAR Multiline







































































Search results

Summary of Contents for LITHOSTAR Multiline

Reviews:

Related manuals for LITHOSTAR Multiline

Brands by name

Popular brands

Siemens LITHOSTAR Multiline, Installation Instructions Manual

Search results

Summary of Contents for LITHOSTAR Multiline

Reviews:

Related manuals for LITHOSTAR Multiline

Brands by name

Popular brands