Siemens LITHOSTAR Multiline Installation Instructions Manual Download

Page: 38 / 70

LITHOSTAR Multiline

RXL2-120.812.01

Page 16 of 20

Siemens AG

System

Rev. 02

10.04

CS PS 24

Medical Solutions

3 - 16

Connections with POLYDOROS LX 30

Connections/harness locations in the generator cabinet (Part C)

•

Route the harnesses in the generator cabinet as shown in Fig. 13 above, and connect
them in accordance with Table 10:

Generator power line connection

Nominal Line Voltage: 400 V ± 10%.

•

Secure the screw type terminals from the service packet to the conductors of the power
cable. If the power cable diameter is small enough, turn the clamps 180° (both curva-
tures opposite to each other).

•

Insulate the harness terminals that have been installed using heatshrink tubing.

•

Remove the cover over the knife breakers F1, F2 and F3 (

/Fig. 13) at the M16 of the

generator.

•

Connect the power line leads L1, L2, L3, N, PE to the fuses F1, F2, F3
(connection

/Fig. 13) and to terminal strip K20. N and

•

Strain-relieve the power cable on the bottom plate of POLYDOROS LX. Do not allow this
to connect to any existing shielding on the power cable.

•

Reinstall the cover over the knife breakers.

Fig. 13

F1 F2 F3

K20

SNT

D110

D115

D220

D100

D160

M16

D165

D200

X41

X200

A... D

K30

F1 F2 F3

K20

SNT

D110

D115

D220

D100

D160

M16

D165

D200

X41

X200

A... D

K32/K31

K30

Summary of Contents for LITHOSTAR Multiline







































































Search results

Summary of Contents for LITHOSTAR Multiline

Reviews:

Related manuals for LITHOSTAR Multiline

Brands by name

Popular brands

Siemens LITHOSTAR Multiline, Installation Instructions Manual

Search results

Summary of Contents for LITHOSTAR Multiline

Reviews:

Related manuals for LITHOSTAR Multiline

Brands by name

Popular brands