Siemens LITHOSTAR Multiline Page 22 Installation Instructions Manual Download

Page: 22 / 70

LITHOSTAR Multiline

RXL2-120.812.01

Page 14 of 14

Siemens AG

System

Rev. 02

10.04

CS PS 24

Medical Solutions

2 - 14

System Installation

Installing the Simomed N44 monitor (OPTIONAL)

•

Remove the monitor housing.

•

Slide the monitor onto the holder of the monitor trolley. The monitor should lock into
position.

•

Tighten the two rear screws.

•

Connect the cables according to the labels.

•

Clamp the shielding of the BAS lead under the clamp of the VIDEO

cable.

•

Establish the protective conductor connections.

•

Reinstall the monitor housing.

Refer also to installation instructions RX53-020.031.06..

System with Polydoros LX

chapter 3

System with Polydoros SX

chapter 4

NOTICE

Summary of Contents for LITHOSTAR Multiline







































































Search results

Summary of Contents for LITHOSTAR Multiline

Reviews:

Related manuals for LITHOSTAR Multiline

Brands by name

Popular brands

Siemens LITHOSTAR Multiline, Installation Instructions Manual

Search results

Summary of Contents for LITHOSTAR Multiline

Reviews:

Related manuals for LITHOSTAR Multiline

Brands by name

Popular brands