manualshive.com logo in svg

Siemens LITHOSTAR Multiline, Installation Instructions Manual

Share
Download
Siemens LITHOSTAR Multiline Installation Instructions Manual Download Page 18

LITHOSTAR Multiline

 

RXL2-120.812.01

Page 10 of 14

Siemens AG

System

Rev. 02

10.04

CS PS 24

Medical Solutions

2 - 10

System Installation

 

Back panel of the PC

2

Positioning/Connecting the Operating System Unit (PC)

2

•

Open the door on the console table and pull out the PC slide-out shelf.

•

Position the operating system unit on PC slide-out shelf and secure it from below.

•

Connect the cables for the mouse, the keyboard, the monitors and the DUEP cable at the 
PC (Fig. 17).

•

Connect the power line cable to the operating system unit.

•

Insert the slide-out shelf. Pay attention to the cable routing in the console.

Cover the cable outlet

2

•

In areas where UL regulations apply,(e.g. USA) you must cover the cable outlet with the 
extra aluminum sheet located in the operating console as fire protection.

Positioning/Connecting DICOM Connect (Option)

2

•

Perform installation and startup according to the manual RXL2-120.814.02..

Fig. 17

DICOM can be built into the LITHOSTAR Multiline only if no 
MULTISPOT is installed.

LM - Control Unit

X51

6

1

2

4

7

X50

1 Keyboard port
2 Mouse port
4 Monitor power line connector
6 Monitor port
7 Power line connector

X50 Respirator-ECG signal interface

X51 DUEP port

NOTICE

Summary of Contents for LITHOSTAR Multiline







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands