manualshive.com logo in svg

Siemens LITHOSTAR Multiline, Installation Instructions Manual

Share
Download
Siemens LITHOSTAR Multiline Installation Instructions Manual Download Page 28

LITHOSTAR Multiline

 

RXL2-120.812.01

Page 6 of 20

Siemens AG

System

Rev. 02

10.04

CS PS 24

Medical Solutions

3 - 6

Connections with POLYDOROS LX 30

 

Fig. 4

Connections of the options and their 
cable locations in the A12 
electronics cabinet and generator AC

3

•

Attach the special cables for the 3rd monitor to the 
rail at the bottom of the electronics cabinet A12.
Install the cables as shown in Fig. 4 and connect 
them according to table 4.

Patient monitor connection 

•

Position the patient monitor in the location provided 
per the project planning guide (e.g. ceiling support).

•

Plug the cable into the "SYNC" connector of the 
patient monitor.

•

Connect the patient monitor to its own power supply, 
i.e. one that is independent of the LITHOSTAR 
Multiline.

Do not establish any protective 
conductor connections to the
LITHOSTAR.

9

CAUTION

VIDEOMED

-DIM-

Rail for cable harness

Cable harness, green, from the operating console

Cable harness, green, from the unit (K3, K4....)

Cable harness, green, from the unit (K8, K9....)

3rd monitor on the monitor trolley (option)

Video cable 3rd monitor

Power Supply

M16

System

Controller

N11

Image Storage

8

7

6

9

4

5

10

A12

Summary of Contents for LITHOSTAR Multiline







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands