manualshive.com logo in svg

Siemens LITHOSTAR Multiline, Installation Instructions Manual

Share
Download
Siemens LITHOSTAR Multiline Installation Instructions Manual Download Page 44

LITHOSTAR Multiline

 

RXL2-120.812.01

Page 2 of 24

Siemens AG

System

Rev. 02

10.04

CS PS 24

Medical Solutions

4 - 2

Connections with POLYDOROS SX 65

 

Fig. 2

Connections and cable locations in the A12 
electronics cabinet

4

(green cable harnesses)

•

Attach the 3 cable harnesses (green) with the cable clip to the rail that is 
installed at the bottom of the electronics cabinet.

•

Secure the braided shield of the zipper hoses to the locations provided.

•

Route the cables in the A12 electronics cabinet as shown in the adjacent 
Fig. 2 and connect them according to tables 1 and 3.
The numbers or letters (e.g.

) are located in the cable lists on the 

following pages.

•

Prior to routing the system cables, remove the EMC shielding plate at 
N11 D11.

right

- cable harness,green, from operat. console

center - cable harness,green, from unit (K3, K4....) 

left

- cable harness, green, from unit (K8, K9....)

4

VIDEOMED

-DIM-

Mounting rail for cable harness

Cable harness, green, from the control console

Cable harness, green, from unit (K3, K4....)

Cable harness, green, from unit (K8, K9.....)

3rd monitor on monitor trolley (optional)

Video cable 3rd monitor

Power Supply

M16

System

Controller

N11

Image Storage

8

7

6

9

4

4

5

10

A12

D21

X4

X14

X3

L2

L1

X15

L1.1

L1.2

Summary of Contents for LITHOSTAR Multiline







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands