manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 10

Table of contents 

 

  

 

ET 200M 

8

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

4 

Installation ............................................................................................................................................... 59 
4.1 

Overview ..................................................................................................................................... 59 

4.2 

Installation ................................................................................................................................... 59 

4.2.1 

Mounting Sequence .................................................................................................................... 59 

4.2.2 

Installing the DIN rail................................................................................................................... 60 

4.2.3 

Installing modules on the mounting rail (standard installation)................................................... 63 

4.2.4 

Installing Active Bus Modules and Modules (Configuration with Active Bus Modules) .............. 66 

4.2.5 

After installation........................................................................................................................... 68 

4.3 

Setting the PROFIBUS address.................................................................................................. 69 

5 

Connecting .............................................................................................................................................. 71 
5.1 

Overview ..................................................................................................................................... 71 

5.2 

Connecting PROFIBUS DP......................................................................................................... 71 

5.2.1 

Connecting the Bus Connector ................................................................................................... 71 

5.2.2 

Connecting the Fiber-Optic Cable to the IM 153-2 FO ............................................................... 72 

5.3 

Connecting PROFINET IO.......................................................................................................... 75 

5.3.1 

Connecting IM 153-4 PN............................................................................................................. 75 

5.4 

Wiring the power supply and modules........................................................................................ 78 

5.4.1 

Wiring rules ................................................................................................................................. 78 

5.4.2 

Wiring the Power Supply and IM 153-x....................................................................................... 79 

5.4.3 

Wiring front connectors of the signal modules............................................................................ 81 

5.4.4 

Connecting shielded cables via a shield connecting element..................................................... 85 

6 

Commissioning ........................................................................................................................................ 89 
6.1 

PROFIBUS DP............................................................................................................................ 89 

6.1.1 

Commissioning the DP slave ...................................................................................................... 89 

6.1.2 

IM 153-1 start-up......................................................................................................................... 91 

6.1.3 

IM 153-2 / 153-2 FO start-up....................................................................................................... 92 

6.1.4 

PROFIBUS DPV1 operation ....................................................................................................... 95 

6.2 

PROFINET IO ............................................................................................................................. 96 

6.2.1 

Configuring in STEP 7................................................................................................................. 96 

6.2.2 

Configuring by means of GSD file............................................................................................... 97 

6.2.3 

Assigning device names to the I/O device.................................................................................. 98 

6.2.4 

Configuring ports of the IM 153-4 PN ....................................................................................... 100 

6.2.5 

Commissioning ET 200M for PROFINET IO............................................................................. 101 

6.2.6 

Startup of ET 200M on PROFINET IO...................................................................................... 102 

7 

Maintenance and service....................................................................................................................... 103 
7.1 

Wiring of the ET 200M .............................................................................................................. 103 

7.2 

Replacing the Power Supply Module ........................................................................................ 103 

7.3 

replacing the IM 153-1 .............................................................................................................. 104 

7.4 

Replacing the IM 153-2 or IM 153-2 FO ................................................................................... 105 

7.5 

Replacing IM 153-4 PN............................................................................................................. 109 

7.6 

Replace modules without the function "Change During Operation" ......................................... 110 

7.7 

Replace modules with the function "Change During Operation" .............................................. 113 

7.8 

Replacing the bus module......................................................................................................... 115 

7.9 

Exchanging fuses in digital output modules.............................................................................. 116 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands