manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 66

Installation 

 

4.2 Installation 

 

ET 200M 

64

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

Sequence when hanging the modules  

Hang the modules onto the rail as follows: 
1.

 

Power supply module 

2.

 

IM 153-x 

3.

 

Signal module(s) 

 

 

 

Note 
If you are installing SM 331 analog input modules, please check before installation 

whether you have to move the measuring range submodules on the side of the module. 

(Refer to chapter "Analog modules" in the "S7-300 automation system, module 

specifications (

http://support.automation.siemens.com/WW/view/en/8859629

)" reference 

manual.) 

 

Sequence for Installation 

Proceed as follows to install the modules: 

Table 4- 3 

Installing modules on mounting rails 

Step 

Activity 

Figure 

1. 

Hook the power supply unit PS 307 onto the rail 

and screw it tight. 

 

2. 

Clip on the bus connector. 
A bus connector is included with each signal 

module, but not however with the IM 153-x. When 

installing the bus connector always start with the IM 

153-x: 

•

 

Take the bus connector from the "last" module 

and insert it in the IM 153-x. 

•

 

Do not plug a bus connector into the "last" 

module. 

Do not insert any bus connectors between the PS 

307 and IM 153-x! 

(7

 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands