manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 102

Commissioning 

 

6.2 PROFINET IO 

 

ET 200M 

100

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

6.2.4

 

Configuring ports of the IM 153-4 PN 

Introduction  

The IM 153-4 PN interface module can diagnose both of its ports: X1 P1 and X1 P2. 

Requirement 

●

 

The ports must be configured in HW Config. 

●

 

The port diagnostics must be released. 

Configuring ports in HW Config  

Configure both ports of the IM 153-4 PN in HW Config in the "Properties of the IM 153-4 PN 

port..." dialog: 
●

 

Addresses tab:  

Specify the diagnostic address of each port. 

●

 

Topology tab: 
Specify a "Port interconnection". 

●

 

Options tab: 
To enable the port diagnostics, select the following for "Connection" under "Transmission 

Medium / Duplex": "Automatic Settings (monitor)". 

Reference 

See 

STEP 7 Online Help. 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands