Siemens IM 153-4 PN Operating Instructions Manual Download Page 43

Page: 43 / 274

Assignment planning

3.5 Configuring the mechanical structure

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

Permissible Ambient Temperature

The following ambient temperature ranges are available:
●

In horizontal mounting position: From 0°C to 60 °C

●

In vertical mounting position: From 0°C to 40 °C

When configuring the ET 200M with IM 153-1AA8x or IM 153-2BA8x (outdoor) and

SIPLUS S7-300 modules the specified temperature range extends up to -25 °C.

3.5.2

Clearance Measurements

Controlling

If you adhere to the minimum clearance measurements:
●

you will guarantee heat dissipation of the S7-300 modules.

●

you will have sufficient space to insert and remove the S7-300 modules.

●

You have sufficient space for running cables.

Using a shielding contact element you can connect shielded lines directly with the rail. This

increases the S7-300 rack´s installation height to 185 mm! You must nevertheless adhere to

the distance of 40 mm.

Clearance Measurements

The following figure shows you the clearance measurements to nearby cable ducts,

apparatus, cabinet walls etc. for an ET 200M installation.
If you use a shield contact element, the dimension specifications apply from the lower edge

of the shield contact element.

Figure 3-6

Clearance measurements for an ET 200M installation on a mounting rack

Summary of Contents for IM 153-4 PN



















































































































































































































































































Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands

Siemens IM 153-4 PN, Operating Instructions Manual

Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands