manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 48

Assignment planning 

 

3.5 Configuring the mechanical structure 

 

ET 200M 

46

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

Installation Options 

Dependent on the length of the rails you can fit up to 9 active bus modules:      

%0

%0

%0

%0

%0,0,0

%036,0

%0

5HGXQGDQFHZLWK
[,0

,0[IRUಯ0RGXOHV
FKDQJHLQRSHUDWLRQರ

PD[LPXP%0[RU%0[

IRU[PPZLGH,2PRGXOHV
60)0KHUH\RXUHTXLUHPD[LPXPEXV
0RGXOHVIRUDQ(70

IRUPPZLGH,2
0RGXOHV60)0&3

 

Figure 3-9 

Configuration with active bus modules 

Placement of the PS 307 power supply modules 

 

Redundancy with 2 x IM 

153-2 

If you use the 530 mm rail, place the BM IM/IM in the right-hand of the 

two latched positions on the rail Then you can install either 2 x PS 

307; 2A or 1 x PS 307; 5A to the rail to the left of the BM IM/IM. 
Otherwise you must fit the power supply modules to a separate S7 

standard rail. 
Recommendation: Each IM 153-2 has its own PS. 

IM 153-1 /-2 for "Module 

change in operation" 

Alongside the IM 153-x, the PS 307; 2A is also compatible with the 

BM PS/IM.  

The PS 307; 5A or 10A are not compatible with the BM PS/IM. You 

must fit these to a separate S7 standard rail. 

See also 

Order Numbers for the ET 200M (Page 247) 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands