Siemens IM 153-4 PN Operating Instructions Manual Download Page 36

Page: 36 / 274

Assignment planning

3.1 Structure variants for PROFIBUS DP

ET 200M

Operating Instructions, 12/2008, EWA-4NEB780600602-08

Structure variants in the outdoor area

Using the existing hardware you can realize the combinations listed in the following table in

the outdoor area.

Table 3- 2

ET 200M structure variants in the outdoor area

non-redundant configuration

redundant configuration

•

IM 153-2 + bus connector

+ I- / O-modules*

•

BM IM/IM (7HD80) + IM 153-2

+ BM 2 x 40 / BM 1 x 80 (painted) *

+ I- / O-modules*

•

BM IM/IM (7HD80) + 2x IM 153-2

+ BM 2 x 40 / BM 1 x 80 (painted) *

+ I- / O-modules*

* SIPLUS modules for use in expanded environmental conditions
In the table, IM 153-2 stands for IM 153-2 (6ES7153-2BA81-0XB0 or 6ES7153-2BA82-0XB0)

SIPLUS modules
For the outdoor area under the product names SIPLUS special S7-300 modules are

available. You can use these under expanded environmental conditions. Expanded

environmental conditions mean:
●

can be used from –25 °C to +60 °C

●

occasional, brief condensation is permitted

●

increased mechanical load permitted

In the functional scope and in the technical data, the SIPLUS modules correspond to the

"standard" modules.
The SIPLUS S7-300 modules have their own order numbers. These are based on those of

the "standard" S7-300 modules, starting however with "6AG1…" instead of "6ES7…".
For more information on these modules, refer to the reference manual "S7-300 automation

system, module specifications

(

http://support.automation.siemens.com/WW/view/en/8859629

)".

You´ll find more information on SIPLUS and contact partners for this area in the Internet

(

http://www.automation.siemens.com/siplus/index_76.htm

Reference

●

You´ll find detailed information regarding the functions and properties of the IM 153-2 in

chapter "Functions (Page 129)" and in the appendix "Functions (Page 129)".

●

You´ll find detailed information on mechanical and climatic environmental conditions for

operating the ET 200M in chapter "General technical specifications of the reference

manual "S7-300 automation system, module specifications

(

http://support.automation.siemens.com/WW/view/en/8859629

)".

●

The IM 153-2Bxx1 is not just an interface module for the ET 200M, but also for the bus

connections DP/PA-link and Y-link. For the configuration variant options please refer to

the "DP/PA Link and Y Link bus links

(

http://support.automation.siemens.com/WW/view/en/1142696

)" operating instructions.

Summary of Contents for IM 153-4 PN



















































































































































































































































































Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands

Siemens IM 153-4 PN, Operating Instructions Manual

Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands