manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 258

Glossary 

 

  

 

ET 200M 

256

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

Fiber-optic cable 

Fiber-optic cables are made from fibere-optics or plastic and have an extremely high 

transmission rate. They are resistant to electromagnetic interference and practically tap-

proof.  

FREEZE 

is a control command that is issued by the DP master to a set of DP slaves.  
Upon receiving the FREEZE control command the DP slave freezes the inputs at their 

current states and transfers them to the DP master in cycles. 
After each received FREEZE the DP slave freezes the input state again. 
The DP slave will cyclically transfer the input data to the DP master only after the DP master 

has issued the UNFREEZE control command. 

Functional grounding 

This grounding method is used to ensure that the electrical product is functioning as 

expected. Functional grounding short-circuits any noise voltage that might render a product 

impermissible.  

Ground 

Conductive ground has an electrical potential of zero.  
Close to ground electrodes the ground's potential might be different from zero. The term 

"reference ground" is frequently used to describe this situation. 

Ground-free 

No galvanic connection to → ground  

Grounding 

Grounding involves connecting an electrically conductive part with the ground electrode 

through a grounding system.  

GSD file 

The properties of a PROFINET device are described in a GSD file (Generic Station 

Description), which contains all required information for the configuration. 
You can integrate PROFINET devices in STEP 7 using a GSD file similar to PROFIBUS 

devices.  
In the case of the PROFINET IO the GSD file is in XML format. The structure corresponds to 

ISO 15734, the worldwide standard for device specifications. 
For PROFIBUS, the GSD file is in ASCII format (according to IEC 61784-1:2002 Ed1 CP 

3/1).  

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands