manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 106

Maintenance and service 

 

7.3 replacing the IM 153-1 

 

ET 200M 

104

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

Response of the ET 200M After Module Replacement 

If there is an error after replacing the module, with 

STEP 5 or STEP 7 you can view the 

cause of the error in the diagnostics buffer. 

7.3

 

replacing the IM 153-1 

Initial Situation 

The IM 153-1 is installed. A new IM 153-1 of the same type should be installed.  

Slot numbering 

If you have provided the modules in your system with slot numbering, when replacing 

modules you must remove the numbering from the old module and then reuse it in the new 

module. 

Pull out the bus connector 

You can remove the bus connector with worn-through bus cable from the PROFIBUS DP 

interface without having to interrupt the data traffic to the bus. 

 

 

Note 
A data communication error may occur on the network. 
A bus segment must always be terminated at both ends with the terminating resistor. For 

example, this is not the case when the last slave with the bus connector is deactivated. As 

the terminating resistor in the bus connector obtains its voltage from the node, the function of 

the terminating resistor is affected. 
Ensure that the nodes to which the terminating resistor is connected are always supplied 

with voltage.  

Tip: Use the PROFIBUS terminator as an active bus connector. 

 

Removing a Module 

To remove the module, proceed as follows: 
1.

 

Switch the on / off switch of the power supply module to position 0 ( : output voltages 

0 V). 

2.

 

Tighten the bus connector. 

3.

 

Disconnect the wiring. 

4.

 

Loosen the fixing screws of the IM 153-1. 

5.

 

Swing out the IM 153-1. 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands