manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 71

 

Installation 

 

4.3 Setting the PROFIBUS address 

ET 200M 
Operating Instructions, 12/2008, EWA-4NEB780600602-08 

69

 

4.3

 

Setting the PROFIBUS address 

Definition 

Each bus node must receive a PROFIBUS address to identify it uniquely on the PROFIBUS 

DP.     

Controlling 

The following rules apply for the PROFIBUS address of the IM 153-x: 
●

 

Permissible PROFIBUS addresses are: 1 to 125. 

●

 

Each PROFIBUS address can be allocated only once on the bus. 

Setting the PROFIBUS Address 

1.

 

Set the PROFIBUS address using a screwdriver and with the door open. 
The PROFIBUS address is the addition of the switch that is located on the right ("ON" 

position). 

 

 

 

Note 
In the IM 153-2Bx00 and the IM 153-2Bxx1 the PROFIBUS address has an 8-pin DIL 

switch instead of the 7-pin switch that has been used up until now. 
The lowest switch has no function and is labeled with "0" or "-" in order to maintain the 

addition principle.  

 

Example: Setting the PROFIBUS Address 

 

IM 153-1, IM 153-2Ax0x 

IM 153-2Bx00 

IM 153-2Bxx1 


21

0
/
0

'&9

%86
$''5(66

 

%86


21

0
/
0

'&9

$''5

 

%86


21

0
/
0

'&9

$''5

ಥ

 

PROFIBUS address: 

64 + 32 + 2 + 1 = 99 

PROFIBUS address: 

64 + 32 + 2 + 1 = 99 

Switch 0 has no function. 

PROFIBUS address: 

64 + 32 + 2 + 1 = 99 

The switch "-" has no function. 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands