Siemens IM 153-4 PN Operating Instructions Manual Download Page 15

Page: 15 / 274

Product overview

1.3 What is PROFINET IO?

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

1.3

What is PROFINET IO?

Definition

PROFINET IO is an open transmission system with real-time functionality defined in

accordance with the PROFINET standard. This standard defines a manufacturer-

independent communication, automation and engineering model.
Accessories for wiring the PROFINET components are available in industrial quality.
●

PROFINET discards the hierarchical PROFIBUS master/slave concept and deploys a

provider/consumer principle instead. The modules of an I/O device that will be subscribed

to by an IO controller are defined within the engineering phase.

●

The quantity framework is extended in accordance with the options offered on

PROFINET IO. Parameter limits are not exceeded during configuration.

●

The transmission rate is 100 Mbps.

●

The configuration interface for users is generally the same as that on PROFIBUS DP (the

system is configured in STEP 7 > HW CONFIG).

Topology of a PROFINET IO network

The figure below shows a typical PROFINET IO network topology. Existing PROFIBUS

slaves can be integrated using an IE/PB link.

(70

3*3&

IO-Controller

S7-300

IO-Device

ET 200pro

PROFINET IO

(Industrial

Ethernet)

Switch

IE/PB-

Link

PROFIBUS DP

ET 200S

OP 25

max. 100 m

Figure 1-2

Typical structure of a PROFINET IO network

Summary of Contents for IM 153-4 PN



















































































































































































































































































Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands

Siemens IM 153-4 PN, Operating Instructions Manual

Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands