manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 88

Connecting 

 

5.4 Wiring the power supply and modules 

 

ET 200M 

86

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

Installing the Shield Contact Element 

Install the shield contact element as follows: 
1.

 

Push the two bolts of the fixing bracket into the guide on the underside of the rail. Position 

the fixing bracket under the modules to be wired. 

2.

 

Bolt the fixing bracket tight to the rail. 

3.

 

A slotted web is arranged at the bottom side of the terminal element. Place the shield 

terminal at this position onto the edge of the fixing bracket (see the figure). 

1

2

2

 

4.

 

Press the shield terminals down and swing them into the desired position. 
You can attach up to four terminal elements on each of the two rows of the shield contact 

element. 

1

2

 

Figure 5-4 

Placing shielded 2-wire lines on the shield contact element 

① 

Fixing bracket 

② 

Shield terminals 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands