manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 224

Interrupt, error and system messages 

 

9.2 PROFINET IO 

 

ET 200M 

222

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

Triggering a maintenance interrupt 

The CPU interrupts processing of the user program and executes the OB 82 diagnostic block 

instead. The event that triggered the interrupt is entered in the OB 82 start information.  

9.2.4

 

Maintenance interrupts 

Introduction 

The PROFINET interfaces of the IM 153-4 PN support the diagnostic and maintenance 

concept in PROFINET in accordance with IEC 61158-6-10. The goal is early detection and 

correction of potential faults.  
For the IM 153-4 PN, maintenance interrups signal the user when network components must 

be checked or replaced. 

Maintenance interrupts  

The IM 153-4 PN signals a maintenance interrupt to the higher-level diagnostic system when 

the following events occur: 

 

Maintenance interrupts 

Event 

Message / Meaning 

Loss of 

synchronization 

•

 

No synchronization frame received 
After parameter assignment or during operation, the sync master did 

not receive a synchronization frame within the timeout period. 

•

 

Jitter lies outside the limits 
–

 

The maximum permissible jitter has been exceeded during 

synchronization. 

–

 

A sync slave has been synchronized by the sync master again. 

Level 1: 

Maintenace required 

Network error 

•

 

Frames rejected 

1

 

The integrated switch has rejected 3 frames due to network overload. 

Level 2: 

Maintenace demanded 

Network error 

•

 

Frames rejected 

1

 

The integrated switch has rejected 10 frames due to network overload.

1

 These diagnostic messages are deleted automatically after 1 second. 

System alarms in 

STEP 7

 

The maintenance information is generated in 

STEP 7 with the following system alarms: 

●

 

Maintenance required - symbolized by a yellow wrench for each port 

●

 

Maintenance demanded, symbolized by an orange wrench for each port 

See also 

Evaluating the interrupts of the ET 200M (Page 221) 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands