manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 126

Maintenance and service 

 

7.11 Saving data and updating the IM 153-4 PN 

 

ET 200M 

124

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

7.11

 

Saving data and updating the IM 153-4 PN 

Storage medium 

A SIMATIC Micro Memory Card is used as the storage medium for the IM 153-4 PN. The 

MMC can be used as a portable data medium.   
On a SIMATIC Micro Memory Card you can save either technology data (device name) or 

data for a firmware update. 

Service life of a SIMATIC Micro Memory Card    

The service life of a SIMATIC Micro Memory Card depends essentially on the following 

factors: 
●

 

Number of deletion or programming operations 

●

 

external influences, such as ambient temperature 

At an ambient temperature up to 60 °C, the useful life of a SIMATIC Micro Memory Card is 

10 years at a maximum of 100,000 delete/write operations. 

Plug-in SIMATIC Micro Memory Cards   

The following memory modules are available: 

Table 7- 3 

Available SIMATIC Micro Memory Cards 

Type 

Order number 

SIMATIC Micro Memory Card 64k 

6ES7953-8LF20-0AA0 

SIMATIC Micro Memory Card 128k 

6ES7953-8LG11-0AA0 

SIMATIC Micro Memory Card 512k 

6ES7953-8LJ20-0AA0 

SIMATIC Micro Memory Card 2M 

6ES7953-8LL20-0AA0 

SIMATIC Micro Memory Card 4M 

6ES7953-8LM20-0AA0 

SIMATIC Micro Memory Card 8M 

6ES7953-8LP20-0AA0 

A SIMATIC Micro Memory Card 64k is sufficient for saving the device name. The SIMATIC 

Micro Memory Cards with at least 2 MB of storage capacity are required when conducting a 

firmware update. 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands