manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 40

Assignment planning 

 

3.3 Configuration possibilities for PROFIBUS DP 

 

ET 200M 

38

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

3.3.3

 

Configurable FM in a configuration with IM 153-2 

Example configuration with IM 153-2 and FM 

The following figure shows an example of an ET 200M with IM 153-2 and in each case two 

SM and two FM of the S7-300 I/O modules. Via the IM 153-2 the S7 DP master or the 

PD / OP can communicate directly with the configured FM (the thick line represents the 

communication path). Configurable FM are, for example, the FM 353 / 354 / 355.  
The following S7 functions are supported by the IM 153-2: 
●

 

Assigning FM parameters via the DP mater CPU 

●

 

Commissioning and diagnosing the FM via a PD / PC 

●

 

Operating and monitoring the FM via an OP 

Refer to the appendix "Compatibilities between the versions of IM 153-2 / -2 FO (Page 243)" 

to see if the DP master you are using and the FM also comply with this functionality for 

distributed FM. 

1

2

3

4

5

 

Figure 3-3 

Configurable FM in an ET 200M with IM 153-2 

 

① 

CPU 315-2 DP as a DP Master 

② 

IM 153-2 

③ 

PROFIBUS DP 

④ 

PG 

⑤ 

OP 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands