manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 30

Brief instructions on commissioning 

 

2.1 Commissioning on PROFIBUS DP 

 

ET 200M 

28

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

5.

 

Set the following parameters: 
–

 

in the dialog box DP slave properties for ET 200M 

adopt the default settings 

–

 

in the dialog box DP slave properties for SM 321, slot 4 in the configuration table  

diagnosis: No load voltage yes 

Diagnostic alarm: Yes 

–

 

in the dialog box DP slave properties for SM 322, slot 5 in the configuration table (see 

following figure) 

 

Figure 2-5 

dialog box Properties - DP Slave for SM 322 

6.

 

Save and compile the configuration. 

7.

 

Download the configuration to the CPU 315-2. 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands