manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 42

Assignment planning 

 

3.4 Structure variants and configuration possibilities for PROFINET IO 

 

ET 200M 

40

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

Redundant operation of the ET 200M on an S7-400H 

Note the general rules for the structure of an H system. 
You will find the general rules for the structure of an H system in the "S7-400H, – fault-

tolerant systems (

http://support.automation.siemens.com/WW/view/en/1186523

)" system 

manual. 

3.4

 

Structure variants and configuration possibilities for PROFINET IO 

Structure variants and configuration possibilities for PROFINET IO can be found in the 

"PROFINET System Description 

(

http://support.automation.siemens.com/WW/view/en/19292127

)" system manual. 

3.5

 

Configuring the mechanical structure 

3.5.1

 

Horizontal or vertical configuration 

Installation Options 

You can install the ET 200M horizontally or vertically.  
Always arrange the power supply and IM 153-x to the left or below. 

 

① 

Power supply, then IM 153-x 

Figure 3-5 

Horizontal and vertical installation of an ET 200M 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands