manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 122

Maintenance and service 

 

7.10 Updating the IM 153-x 

 

ET 200M 

120

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

Carry out an update via SIMATIC Micro Memory Card as follows: 
1.

 

Use 

STEP 7 and your programming device to transfer the update files to a SIMATIC 

Micro Memory Card. The data saved on the SIMATIC Micro Memory Card is then 

overwritten by the update files. 

3*3&

 

2.

 

Switch off the IM 153-2 and insert the SIMATIC Micro Memory Card with update. 

(70

,0

 

3.

 

Switch on the power. 
–

 

The IM 153-2 automatically detects the SIMATIC Micro Memory card with the update 

files and starts the update. 

–

 

During the update the SF and the BF LEDs light up. 

–

 

After the update is concluded the BF LED flashes at 0.5 Hz. 

4.

 

Switch off the IM 153-2 and insert the SIMATIC Micro Memory card with update. 
To eject the SIMATIC Micro Memory card, push in the ejector with a small screwdriver or 

ball-point pen. 

Update in the Redundant System 

When the update of the active IM 153-2 takes place via PROFIBUS DP, the concluding reset 

automatically triggers the changeover procedure between the two IM 153-2s. We 

recommend that you then carry out an update of the second IM 153-2 in the redundant 

system. The update must be conducted separately for each IM 153-2. 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands