manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 149

 

Functions 

 

8.2 Time stamping the input signals with IM 153-2 

ET 200M 
Operating Instructions, 12/2008, EWA-4NEB780600602-08 

147

 

8.2.4.2

 

Operating principle 

●

 

The 240 data record is the configured data record for the time stamping on the ET 200M.  

It defines which modules and which input channels of which type can be called upon by 

the IM 153-2 for the time stamping.  

When accepting the data record 240 the consistency of the data record with the 

configured structure of the slave is checked. 
As soon as this data record 240 is transmitted correctly to the IM 153-2 the time stamping 

is activated. 

●

 

If the input signal on one of the monitored inputs changes, this event is time stamped by 

the IM 153-2 and stored in one of hte data records 100 to 114. 

●

 

Then the IM 153-2 triggers a process interrupt. 

●

 

The master reacts with a diagnosis requirement to the slave. 

●

 

The IM 153-2 responds to this with a diagnostic frame. This diagnostic frame includes, 

among other things, the number of the data record that includes the time-stamped 

messages. 

●

 

Because of this diagnostic frame the associated run level "process interrupt" is launched 

in the user program. Within this run level, the user must be able to tell which data record 

is to be read with messages from the IM 153-2. Depending on the application case, the 

user must also ensure multiple calls on this run level. 

In your CPU´s manual, look up DPV1-blocks, e.g. "RALRM". 

●

 

The user program monitors entries in the run level "process interrupt". As soon as an 

entry is detected, the data record is read from the IM 153-2. A block in accordance with 

DPV1 also serves to do this. 

Refer to DPV1-blocks, e.g. "RDREC" in your CPU´s manual. 

●

 

In accordance with the requirements of your application, the data record is saved or 

further processed. Every single signal message comprises 12 bytes, a data record can 

include up to 20 messages. 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands