Siemens IM 153-4 PN Operating Instructions Manual Download Page 105

Page: 105 / 274

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

103

Maintenance and service

7.1

Wiring of the ET 200M

Scope of maintenance

The ET 200M is a maintenance-free DP slave.
Maintenance is limited to the replacement or exchanging of modules or components.

7.2

Replacing the Power Supply Module

Initial Situation

The power supply module you want to replace is installed and wired. You want to install a

new power supply module of the same type.

Slot numbering

If you have provided the Power Supply Modules in your system with slot numbering, when

replacing modules you must remove the numbering from the old Power Supply Modules and

then reuse it in the new Power Supply Modules.

Removing the Power Supply Module

To remove the power supply module, proceed as follows:
1.

Operate the supply isolating switch in order to de-energize the power supply module.

Remove the cover.

Disconnect all the wiring.

Undo the fixing screws of the power supply module.

Swing the power supply module out.

Installing the New Power Supply Module

To install the new power supply module, proceed as follows:
1.

Check the setting of the voltage selector switch.

Hook the new power supply module of the same type onto the rail and swing it down into

place.

Screw the power supply module on securely.

Wire the power supply module.

Connect the power supply module to the line voltage.

Close the cover.

Summary of Contents for IM 153-4 PN



















































































































































































































































































Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands

Siemens IM 153-4 PN, Operating Instructions Manual

Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands