manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 225

 

Interrupt, error and system messages 

 

9.2 PROFINET IO 

ET 200M 
Operating Instructions, 12/2008, EWA-4NEB780600602-08 

223

 

9.2.5

 

Channel diagnostics 

The PROFINET interfaces of the IM 153-4 PN support the diagnostics concept and 

maintenance concept in PROFINET IO in accordance with the standard IEC61158-6-10.  
Diagnostic interrupts use the channel-specific diagnosis according to IEC 61158-6 as 

interrupt information. 
PROFINET IO also permits the reading of diagnostic states via standardized data records. 

For example, the diagnostic state of a module can be read using the data record C00A hex. 
The data record is read by calling SFB 52 RDREC (read data record). 

9.2.6

 

Error types for modules 

For detailed information about the error types for modules of the ET 200M, refer to chapter 

"Identifier-related diagnosis (Page 198)". 

9.2.7

 

Diagnostics of incorrect configuration states of ET 200M on PROFINET IO 

Incorrect module configuration states  

The following incorrect ET 200M configuration states lead to a failure of the ET 200M I/O 

device or prevent data exchange: 
●

 

Number of modules exceeds maximum configuration 

●

 

Faulty backplane bus, for example, defective active bus module  

9.2.8

 

Diagnostics events triggered by a STOP of the I/O controller 

If communication diagnostics of the PROFINET interface ports is triggered when the IO 

controller is in STOP state, these diagnostics will not be signaled after startup of the IO 

controller.    

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands