manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 178

Functions 

 

8.7 Identification and maintenance data (I&M data) 

 

ET 200M 

176

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

8.7.1

 

I&M data for PROFIBUS DP 

As of IM 153-2Bx00 this data is available on the ET 200M. 

 

 

Note 
Only one DP master can access the I&M data of an ET 200M at any one point. 

 

Reading and writing the I&M data with STEP 7 

In 

STEP 7 the I&M data are displayed in the tabs "Module state – IM 153-2" and "DP Slave 

properties" (see online help for 

STEP 7). 

In the HW Config you can enter the modules M data (e.g. in a dialog box during the 

configuration). 
The access to the I&M data takes place in accordance with the IEC 61158-6 standard. 
In the H system the interface module from which the I&M data is to be read must be 

available online.  

Reading and writing the I&M data without STEP 7 

If you wish to use the I&M data without using 

STEP 7, you must carry out the data access in 

accordance with the specifications of the PROFIBUS Guideline – Order No. 3.502, 

Version 1.1 May 2003. 
In the H system the interface module from which the I&M data is to be read must be 

addressed (slot 245 or 246). Slot 245 labels the left interface module, slot 246 the right 

interface module on the BM IM/IM. 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands