manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 223

 

Interrupt, error and system messages 

 

9.2 PROFINET IO 

ET 200M 
Operating Instructions, 12/2008, EWA-4NEB780600602-08 

221

 

9.2.3

 

Evaluating the interrupts of the ET 200M 

Introduction 

The I/O device initiates interrupts when certain errors occur. The interrupt evaluation is 

dependent on the utilized I/O controller. 

Evaluating interrupts with I/O controller  

The ET 200M supports the following interrupts: 
●

 

Diagnostic interrupts 

●

 

Hardware interrupts 

●

 

Removal / insertion interrupts 

●

 

Maintenance interrupts 

In the event of an interrupt, interrupt OBs are executed automatically in the CPU of the IO 

controller (refer to the "SIMATIC software, programming with STEP 7 V5.x. 

(

http://support.automation.siemens.com/WW/view/en/18652056

)" manual). 

Information on the cause and class of the error is already available based on the OB number 

and start information.  
To obtain detailed information about the error event, call the error OB using 

SFB 54 "RALRM" (read additional interrupt information). 

Triggering of a diagnostics interrupt 

In case of an incoming or outgoing event (for example, a wire break), the module triggers a 

diagnostics interrupt if "Enable: Diagnostics interrupt" is set. 
The CPU interrupts processing of the user program and executes the OB 82 diagnostic block 

instead. The event that triggered the interrupt is entered in the OB 82 start information. 

Triggering a hardware interrupt 

If a hardware interrupt occurs, the CPU interrupts the user program execution and executes 

hardware interrupt block OB 40. The event that triggered the interrupt is entered into the 

OB 40 start information. 

 

 

Note 
Hardware interrupts should not be used for technological purposes (cyclic generation of 

hardware interrupts, for example), because these can become lost in the entire system.  

 

Triggering a removal / insertion interrupt 

The CPU interrupts processing of the user program and processes the OB 83 diagnostic 

block instead. The event that triggered the interrupt is entered in the OB 83 start information.  

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands