Siemens IM 153-4 PN Operating Instructions Manual Download Page 99

Page: 99 / 274

Commissioning

6.2 PROFINET IO

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

Procedure

Start SIMATIC Manager.

Create a new project.

Configure the ET 200M with HW Config.

Move the modules from the hardware catalog to the configuration table using a drag-and-

drop operation.

Double-click the first module of the ET 200M in the configuration table, and set its

parameters.

Assign parameters for the other modules of the ET 200M.

Save the configuration, or download it to the I/O controller.

Reference

For additional information, refer to the

STEP 7 Online Help.

6.2.2

Configuring by means of GSD file

Introduction

The GSD file allows you to configure the ET 200M using

STEP 7 V5.4, Service Pack 2 or

higher. To do so you must install the GSD in the configuration software beforehand.

Requirements

You will need a GSD file, available for download from the Internet

(

http://support.automation.siemens.com/WW/view/en/25057900

Interface Module IM 153-4 PN:

GSDML-V1.0-Siemens-ET200M-"date in yyyymmdd format".xml

Configuring the ET 200M on PROFINET IO with

STEP 7

Start

STEP 7 and then select the Tools > Install New GSD file menu command in HW

Config.

Select the GSDML file to install from the next dialog box, then confirm with OK. Result:

The ET 200M appears in the PROFINET IO folder of the hardware catalog.

For additional information, refer to the

STEP 7 Online Help.

Summary of Contents for IM 153-4 PN



















































































































































































































































































Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands

Siemens IM 153-4 PN, Operating Instructions Manual

Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands