Siemens IM 153-4 PN Operating Instructions Manual Download Page 97

Page: 97 / 274

Commissioning

6.1 PROFIBUS DP

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

6.1.4

PROFIBUS DPV1 operation

The ET 200M fulfils the requirements in accordance with DPV1. If you wish to use the DPV1

functions, then the DP master must of course fulfill the requirements in accordance with

DPV1 (refer to the DP master documentation).

Functions of the PROFIBUS DPV1 slave

The following table shows you the new functions of the PROFIBUS DPV1 slave compared

with a PROFIBUS DPV0 slave:

Table 6- 2

Compare the DPV1 and DPV0 slave

Function

DPV0

slave

DPV1

slave

Parameter assignment and configuration with GSD file

Cyclic data exchange

Class 1 services

(parameter

assignment master,

e.g. PLC)

–

Acyclic data traffic

(read / write data record):

•

free access to parameters in the field device

•

Reparameterization of application process

Class 2 services

(e.g. PD / OP)

Diagnosis

•

Identifier-related diagnostics

•

Module status

•

Channel-specific diagnostics

Interrupts

•

Diagnostic interrupt

•

Process interrupt

–

•

removing / insertion interrupt

–

Other functions

•

Time synchronization

–

•

Time stamping

–

•

Isochronous

–

The assignment of the functions to the versions of the interface module can be found in the

"Compatibilities between the IM 153-x (Page 241)" appendix.

If configuring with HW-Config, with some functions S7-specific features are set.

One interrupt can be used per diagnostic frame. With DPV1 (and S7 DP) there is an interrupt that

comprise a slave diagnosis that is accompanied by an acknowledgement mechanism that does not

exist with DPV0.

Up to IM 153-2Bx00 the time stamping is available only in the S7 system environment.

without GSD-file or with GSD rev. 2

with GSD rev. 2

as of GSD rev. 3

only if the GSD-file is imported and if, in HW-Config the DPV1-mode is selected

With S7 DP the interrupts are not reported if the CPU is in STOP.

as of GSD rev. 4

as of GSD rev. 5

Summary of Contents for IM 153-4 PN



















































































































































































































































































Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands

Siemens IM 153-4 PN, Operating Instructions Manual

Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands