manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 65

 

Installation 

 

4.2 Installation 

ET 200M 
Operating Instructions, 12/2008, EWA-4NEB780600602-08 

63

 

Connection of protective conductor 

The following figure shows you how to connect the protective conductor to the rail.    

 

Figure 4-2 

Connecting the protective conductor to the rail 

See also 

Clearance Measurements (Page 41) 

4.2.3

 

Installing modules on the mounting rail (standard installation) 

Accessories 

The accessories you need for installation are included with the modules. The appendix 

"Order Numbers for ET 200M (Page 247)" contains a list of accessories and spare parts with 

the corresponding order numbers.    

Table 4- 2 

Module accessories 

Module 

Included accessories  

Description 

IM 153-x  

1 x slot number label 

For assigning slot numbers 

Bus connectors 

For establishing the electrical connections between the 

modules 

Signal module 

(SM) 

Labeling strip  

For labeling the input and output points on the module 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands