manualshive.com logo in svg

Siemens CU240S DP-F, Operating Instructions Manual

The Siemens CU240S DP-F is a high-performance control unit designed to enhance the efficiency of motor-driven applications. To ensure seamless operations, it is essential to refer to the comprehensive Operating Instructions Manual provided. Download this manual for free from our website, manualshive.com, and make the most of your Siemens CU240S DP-F.

Share
Download
background image

 

Communication 

 

6.2 Cyclic Communication 

Control Units CU240S 
Operating Instructions, 07/2008 - FW 3.2, A5E00766042B AD 

133

 

Table 6-11  Switch over behavior of telegram structures, Part 2 

P0922 =  20 → 1/353 

if P0700 = 

20 → 350  
if P0700 = 

20 → 352/354  
if P0700 = 

20 → 999  
if P0700 = 

 

1, 2, 4 

6 

1, 2, 4 

6 

1, 2, 4 

6 

1, 2, 4 

6 

P0820 =  0.0 

0.0 

no change  2091.4 

8891.4 

0.0 

0.0 

no change 

no change 

P0821 =  no change  no change  no change  2091.5 

8891.5 

no change 

no change  no change 

no change 

P1035 =  no change  2090.13 

8890.13 

no change  2090.13 

8890.13 

no change 

2090.13 

8890.13 

no change 

no change 

P1036 =  no change  2090.14 

8890.14 

no change  2090.14 

8890.14 

no change 

2090.14 

8890.14 

no change 

no change 

 

Table 6-12  Switch over behavior of telegram structures, Part 3 

P0922 = 

350 → 1/353  
if P0700 = 

350 → 20  
if P0700 = 

350 → 352/354  
if P0700 = 

350 → 999  
if P0700 = 

 

1, 2, 4 

6 

1, 2 

4 

6 

1, 2, 4 

6 

1, 2, 4 

6 

P0820 = 

no change  0.0 

no change 2013.15 

2090.15 

8890.15 

no change 0.0 

no change no change

P0821 = 

no change  0.0 

0.0 

0.0 

0.0 

no change 0.0 

no change no change

P1035 = 

no change  2090.13 

8890.13 

19.13 

19.13 

19.13 

no change 2090.13 

8890.13 

no change no change

P1036 = 

no change  2090.14 

8890.14 

19.14 

19.14 

19.14 

no change 2090.14 

8890.14 

no change no change

 

Table 6-13  Switch over behavior of telegram structures, Part 4 

P0922 = 

352 → 1/353  
if P0700 = 

352 → 20  
if P0700 = 

352 → 350  
if P0700 = 

352 → 999/354  
if P0700 = 

 

1, 2, 4 

6 

1, 2 

4 

6 

1, 2, 4 

6 

1, 2, 4 

6 

P0820 = 

0.0 

0.0 

no change 2013.15 

2090.15 

8890.15 

no change 2091.4 

8891.4 

no change no change

P0821 = 

no change  no change  no change no change no change no change 2091.5 

8891.5 

no change no change

P1035 = 

no change  2090.13 

8890.13 

19.13 

19.13 

19.13 

no change 2090.13 

8890.13 

no change no change

P1036 = 

no change  2090.14 

8890.14 

19.14 

19.14 

19.14 

no change 2090.14 

8890.14 

no change no change

 

Summary of Contents for CU240S DP-F









































































































































































































































Reviews:

No comments

Related manuals for CU240S DP-F

National Instruments NI 9215 Calibration Procedure preview
NI 9215
Brand: National Instruments Pages: 8
York MILLENNIUM Manual preview
MILLENNIUM
Brand: York Pages: 20
Parker PWD Series Operation Manual preview
PWD Series
Brand: Parker Pages: 38
Parker Racor RK 30770 Operation And Safety Instructions preview
Racor RK 30770
Brand: Parker Pages: 2
IR-Tec OS-NET Programming Manual preview
OS-NET
Brand: IR-Tec Pages: 14
LOGICDATA DYNAMIC MOTION Configuration Handbook preview
DYNAMIC MOTION
Brand: LOGICDATA Pages: 23
Modine Manufacturing Airedale Sentinel Quick Start Manual preview
Airedale Sentinel
Brand: Modine Manufacturing Pages: 2
T&S B-0108-H Installation And Maintenance Instructions Manual preview
B-0108-H
Brand: T&S Pages: 16
AccessPRO AccessPRO2 Installation And Connection Manual preview
AccessPRO2
Brand: AccessPRO Pages: 2
Transient Modules u1P Manual preview
u1P
Brand: Transient Modules Pages: 5
Danfoss PVE Series Installation Manual preview
PVE Series
Brand: Danfoss Pages: 6
Listen Technologies ListenPoint Quick Reference preview
ListenPoint
Brand: Listen Technologies Pages: 2
Balboa MVP240 Reference Card preview
MVP240
Brand: Balboa Pages: 2
M-Audio Keystation 61es User Manual preview
Keystation 61es
Brand: M-Audio Pages: 15
Byron Home Easy HE-414 Installation Instructions preview
Home Easy HE-414
Brand: Byron Pages: 2
Azbil VY63 Series Specifications & Instructions preview
VY63 Series
Brand: Azbil Pages: 12
Johnson Controls MPS-24A Quick Start Manual preview
MPS-24A
Brand: Johnson Controls Pages: 2
Bamo BAMOWIZ DOZ User Manual preview
BAMOWIZ DOZ
Brand: Bamo Pages: 10

Brands by name

Popular brands

Load more brands