Siemens CU240S DP-F Operating Instructions Manual Download Page 168

Page: 168 / 232

Communication

6.5 Communication via PROFINET

Control Units CU240S

168

Operating Instructions, 07/2008 - FW 3.2, A5E00766042B AD

Table 6-34 Parameters for flexible interconnection of process data

PZD1

STW/ZS

PZD2

HSW/HI

PZD3

PZD4

PZD5

Link values for setpoints master to

inverter

r8850.00 r8850.01 r8850.02 r8850.0

r8850.0

Link parameters for actual values

inverter to master

P8851.0

P8851.

Note
r8850 also acts as a display parameter through which the setpoints received by the

PROFINET interface can be checked.

P8841 PROFINET functions
A number of advanced property settings for the PROFINET interface can be accomplished

using the indexed parameter P8841.
For most applications, however, the defaults values are adequate (value = 0). The following

table shows the property setting options.

Table 6-35 PROFINET functions

Parameter Meaning

Value range

P8841.01

BOP parameter in EEPROM:

Modifications to parameter settings

via SIMATIC HMI are stored

permanently in the EEPROM or as

volatile data in the RAM.

0: Permanent (EEPROM)

1: Volatile (RAM)

P8841.03

Select displayed diagnostics

screen.

0: Standard diagnostics

Process data monitoring
The process data are monitored according to the following parameter:
● P8840 Fieldbus Off-time.

If no telegram is received through the PROFINET interface, the fault F0070 will be

generated. If no telegram is received , Parameter P8840 defines the period of time till the

fault message is generated.
– P8840 = 0 means: No monitoring
– P8840 > 0 means: The period of time in milliseconds

CAUTION

Do not deactivate the process data monitoring function! If the monitoring function is

deactivated, the inverter will not recognize a PROFINET communication failure and

continue to operate with possibly wrong commands and setpoints.

F0070 is activated if no new setpoints are received by the PROFINET interface within the

telegram failure period.

Summary of Contents for CU240S DP-F









































































































































































































































Search results

Summary of Contents for CU240S DP-F

Reviews:

Related manuals for CU240S DP-F

Brands by name

Popular brands

Siemens CU240S DP-F, Operating Instructions Manual

Search results

Summary of Contents for CU240S DP-F

Reviews:

Related manuals for CU240S DP-F

Brands by name

Popular brands