Siemens CU240S DP-F Operating Instructions Manual Download Page 100 | Manualshive

Page: 100 / 232

background image

Commissioning

5.7 Commissioning with the MMC

Control Units CU240S

100

Operating Instructions, 07/2008 - FW 3.2, A5E00766042B AD

Manual Download of a parameter set with an MMC

Prerequisites

●  Supply voltage is active for the download inverter
●  The download inverter is in "Ready State"
●  On the MMC the following folder structure must be available:

/USER/SINAMICS/DATA/clonexx.bin

Procedure

Note
The following important conditions must be fulfilled when using the download procedure:

•

During the download the inverter will not react to any commands.

•

Once the download procedure has started, it cannot be interrupted.

•

After upload and download of parameters between differing Control Units, parameter

settings must be checked.

•

Parameter download from a different CU might fail with F0063 if parameters cannot be

downloaded (Check P949 for the (first) parameter number which cannot be downloaded).

•

If the download fails, the inverter reverts to the previous parameters from the EEPROM.

Parameter

Description (Parameter name and factory setting (if not variable) in bold)

Setting

Insert the MMC to the download inverter and perform the Manual Download according the

flow chart.

P0010 = 30

Commissioning parameter*

0: Ready

1: Quick commissioning

2: Inverter

30: Factory setting, parameter transfer

95: Safety commissioning (for CUs with fail-safe functions only)

P0804 = …

Select Clone file (for download)

0: clone00.bin

…

99: clone99.bin

P0803 = 2

Transfer data to EEPROM

0: Disabled

1: Start BOP Transfer

2: Start MMC Transfer

If the download has been completed successfully, P0010 and P0803 will be set to 0 and the

"RDY" LED is on.

If the upload has failed, F0061 (MMC-PS not fitted), F0062 (MMC-PS contents invalid) resp.

F0063 (MMC-PS contents incompatible) or F0051 (failure while accessing EEPROM) will be

displayed, LED "SF" (red) is on.

In this case insert a proper MMC and attempt another download or perform a factory reset.

After a successful Manual Download the MMC can be removed from the inverter and inserted

into the next download inverter. Then perform the download steps again until the series

commissioning has been completed for all inverters.

«
...
98
99
100
101
102
...
»

Summary of Contents for CU240S DP-F









































































































































































































































Reviews:

No comments

Related manuals for CU240S DP-F

Brand: GE Pages: 2

Brand: XOXO Modular Pages: 13

Brand: Balboa Water Group Pages: 28

Brand: D-Link Pages: 40

Brand: TA Hydronics Pages: 14

Brand: Saga Pages: 9

Brand: Harmonic Drive Pages: 85

Brand: Vacon Pages: 132

Brand: Polycom Pages: 2

Optidrive Elevator

Brand: Invertek Pages: 5

Brand: Techtrol Pages: 4

Brand: Dickey-John Pages: 109

by-me Eikon 20526

Brand: Vimar Pages: 6

Brand: A10 Networks Pages: 2

Brand: Z-Wave Pages: 5

Compact Performance Series

Brand: Festo Pages: 58

Grain PNEG-1509

Brand: GSi Pages: 70

Brand: Junkers Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands