Siemens CU240S DP-F Operating Instructions Manual Download Page 114

Page: 114 / 232

Commissioning

5.9 Parameters

Control Units CU240S

114

Operating Instructions, 07/2008 - FW 3.2, A5E00766042B AD

Quick commissioning

This parameter attribute identifies as to whether the parameter is included in the quick

commissioning (QC) (P0010 = 1).

Table 5-22 Parameter attributes - Quick commissioning

Description

The parameter is not included in the quick commissioning

Yes

The parameter is included in the quick commissioning

Value range

The value range, which is first specified by the data type, is restricted by minimum and

maximum values depending on the quantities of the inverter/motor. The values min and max

are permanently saved in the inverter and cannot be changed by the user. To support

commissioning each write parameter has a default value called factory setting.

Table 5-23 Parameter attributes - Value range

Value range

Description

No value entered (e.g.: "r parameter")

Min

Minimum value

Max

Maximum value

Def

Default value

Data sets

A detailed description for the data sets is given in the respective section

Table 5-24 Data sets

BICO

Description

CDS

Command data set

DDS

Drive data set

Summary of Contents for CU240S DP-F









































































































































































































































Search results

Summary of Contents for CU240S DP-F

Reviews:

Related manuals for CU240S DP-F

Brands by name

Popular brands

Siemens CU240S DP-F, Operating Instructions Manual

Search results

Summary of Contents for CU240S DP-F

Reviews:

Related manuals for CU240S DP-F

Brands by name

Popular brands