Raven RS Lite Calibration And Operation Manual Download Page 92

Page: 92 / 125

HAPTER

Raven RS1™ and RS Lite™ Calibration and Operation Manual

SLINGSHOT AND RTK STATUS

FIGURE 5. Home Page

Display

Message

RS1 is connected to the Slingshot portal.

RS1 is not connected to the Slingshot portal.

RS1 is receiving RTK corrections.

NOTE:

This icon is hidden if RTK corrections have not been unlocked in the

RS1 unit.

RS1 is not receiving RTK connections.

NOTE:

This icon is hidden if RTK has not been unlocked in the RS1 unit or an

RTK correction profile has not been setup on the Slingshot website.

RS1 Remote Diagnostics are being sent to the Slingshot portal.

RS1 Remote Diagnostics are not being sent to the Slingshot portal.

Slingshot

Name

Displays the default System name given to the RS1 in the Slingshot portal when

the device was registered.

RTK Status

Slingshot

Status

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands