manualshive.com logo in svg

Raven RS Lite, Calibration And Operation Manual

Share
Download
Raven RS Lite Calibration And Operation Manual Download Page 94

C

HAPTER

 11

88

Raven RS1™ and RS Lite™ Calibration and Operation Manual

FIGURE 8. Cellular Information Page

IMEI #. 

Displays the International Mobile Equipment Identity number (IMEI#) with the modem installed in the RS1 

unit.

Phone Number. 

Displays the phone number assigned to the SIM card in the RS1 modem when an valid data plan 

is active.

SIM. 

Displays the identification number associated with the SIM card currently in use in the RS1 system.

Network. 

Displays the cellular network the Slingshot is utilizing.

Country. 

Displays the country that the cellular network provides is in.

Network Provider. 

•Displays the cellular network used by the SIM card that is in the modem in the RS1.

NOTE:

Refer to the “Cellular Modem” on page 82 for additional information on cellular settings.

APN Password. 

•Dictated by the cellular provider. This is not applicable for all networks.

FIGURE 9. Cellular Settings Page

Mode. 

Indicates the cellular network mode in which the RS1 receiver is operating.

Roam. 

Allows the user to restrict or allow cellular data usage when the system is not in its home network. This is 

not available on all cellular networks. 

Summary of Contents for RS Lite






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands