Raven RS Lite Calibration And Operation Manual Download Page 107

Page: 107 / 125

016-4010-001 Rev. J

101

SLINGSHOT

FIELD UPDATES

1. From the Slingshot working set home page, select the

Diagnostics

button.

2. On the System Information tab, select the RS1 Information option in the drop-down.
3. Select the

Field Update

button at the bottom of the page.

FIGURE 26. System Information Page

4. Select the

Field Update

button to view the latest software updates for the RS1 unit.

FIGURE 27. Software Download Page

5. Select

Check for Server Updates.

NOTE:

This will search the RS1 system for the latest software updates.

6. Select the desired software update from the list.
7. Select

Accept

NOTE:

The software is downloaded to the RS1 unit, but is not installed in the system until later in the

procedure.

NOTE:

When the button is pressed, the following warning prompt is displayed notifying the user that cellular

data will be used to download the software and asks if the user would like to proceed with the

download.

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands