Raven RS Lite Calibration And Operation Manual Download Page 67

Page: 67 / 125

016-4010-001 Rev. J

DIAGNOSTICS AND TROUBLESHOOTING

DIAGNOSTIC TROUBLE CODE (DTC) LIST

TABLE 1. Diagnostic Trouble Codes

Code ID

Description

Recommended Actions

Maximum engage speed

shutdown.

Machine speed exceeds maximum auto-steer speed.

Auto-steering is disengaged.
Reduce machine speed below maximum engage speed

and re-engage auto-steering. RS1 maximum auto-steer

operating speed is:
• 19.3 km/h [12 mph] for machines operating in Europe

with homologation terms accepted.

• 32.1 km/h [20 mph] for tracked machines and

swathers.

• 46.7 km/h [29 mph] for units capable of high-speed

steering and not subject to homologation terms.

NOTE:

Contact a local Raven dealer for additional

assistance with high-speed steering

unlocks.

.16

Maximum engage speed

warning.

Machine speed is approaching the maximum auto-steer

speed. To maintain auto-steer operation, do not exceed

the maximum auto-steering speed (refer to 74.0 above).
RS1 maximum steering warning DTC is triggered at:
• 16.1 km/h [10 mph] for machines operating in Europe

with homologation terms accepted.

• 29 km/h [18 mph] for tracked machines and

swathers.

• 43.5 km/h [27 mph] for units capable of high-speed

steering and not subject to homologation terms.

NOTE:

Contact a local Raven dealer for additional

assistance with high-speed steering

unlocks.

Maximum speed engage.

Reduce machine speed below maximum engage speed

to engage auto-steering.
RS1 maximum engage speed is:
• 16.1 km/h [10 mph] for machines operating in Europe

with homologation terms accepted.

• 19.3 km/h [12 mph] for tracked machines and

swathers.

• 29 km/h [18 mph] for units capable of high-speed

steering and not subject to homologation terms.

NOTE:

Contact a local Raven dealer for additional

assistance with high-speed steering

unlocks.

Maximum engage speed

engage warning.

Too slow to engage.

Increase machine speed above 0.5 km/h [0.3 mph] (RTK

- 0.1 km/h [0.1 mph]) to engage auto-steering.

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Brands by name

Popular brands