Raven RS Lite Calibration And Operation Manual Download Page 59

Page: 59 / 125

CHAPTER

016-4010-001 Rev. J

CHAPTER 10

DIAGNOSTICS AND

TROUBLESHOOTING

BUTTON DEFINITIONS

STEERING STATUS

FIGURE 1. Home Page

The following are common steering status or mode messages which may occur while the RS1 system is engaged:

Display

Message

Active diagnostic and troubleshooting codes are present. The RS1 system cannot

be engaged in this state.

Active diagnostic and troubleshooting codes are present. The RS1 system can be

engaged in this state, but performance quality may be degraded.

No active diagnostic or troubleshooting codes are present. The RS1 system is

ready to be engaged.

NOTE:

Both the steering wheel and GPS icons must be green in order to

engage the RS1 system.

Steering is engaged, with no active diagnostic or troubleshooting codes present

in the RS1 system.

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Brands by name

Popular brands