Raven RS Lite Calibration And Operation Manual Download Page 96

Page: 96 / 125

HAPTER

Raven RS1™ and RS Lite™ Calibration and Operation Manual

WIFI SETTINGS

FIGURE 12. WiFi Hotspot Settings Page

SSID.

Displays the WiFi SSID (network name). This setting cannot be modified by the operator.

Encryption Type.

Displays the encryption mode being used on the RS1 WiFi hot spot. This setting cannot be

modified by the operator.

Mode.

Select the mode for WiFi or Hotspot operation.

• Manual Client
• Manual Hotspot
• Raven Auto

WiFi Channel.

Displays the channel the WiFi hot spot is currently using. If the operator is experiencing a issues

with connectivity or staying connected, adjusting these settings may improve connectivity issues. This setting can

be modified by the operator. The WiFi password can only be modified through the Slingshot website.

MANUAL CLIENT

Select Manual Client to manually connect to available WiFi networks.

FIGURE 13. WiFi Connection Status

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Brands by name

Popular brands